The family of Products
The SVEA "REG-M" family of products comprises 16 input/output modules with a switching capacity of up to 16A, phase control dimmers, a control device for the 1-10V interface and digital 24V and 230V inputs.
 LON I/O Module REG-M 12DO DC
12 outputs 24V
LON I/O Module REG-M 4DO 8DI DC
4 outputs 24V, 8 inputs 24V
LON I/O Module REG-M 4DI DC-P
4 inputs for dry contacts
LON I/O Module REG-M 8DI DC-P
8 inputs for dry contacts
LON I/O Module REG-M 4DI AC/DC
4 inputs 24V
LON I/O Module REG-M 8DI AC/DC
8 inputs 24V
LON I/O Module REG-M 4DI 230V
4 inputs 230V
LON I/O Module REG-M 8DI 230V
8 inputs 230V
LON I/O Module REG-M 2S
2 relay outputs (10A)
LON I/O Module REG-M 4S 16A
4 relay outputs (16A) with manual control
LON I/O Module REG-M 8S
8 relay outputs (10A) with manual control
LON I/O Module REG-M 8S 16A
8 relay outputs (16A) with manual control
LON I/O Module REG-M 12S 16A
12 relay outputs (16A) with manual control
LON I/O Module REG-M MSE2
4 relay outputs (10A) for 2 drive units
LON I/O Module REG-M MSE4
8 relay outputs (6A) for 4 drive units with manual control
LON I/O Module REG-M DIM 600-AN
Dimmer 600W phase-on control
LON I/O Module REG-M DIM 400-AB
Dimmer 400 W phase-off control
LON I/O Module REG-M DIM 1-10V
1-10V control device
For its top quality, the I/O module REG-M offers an excellent cost-benefit ratio. Particular attention was paid at the development stage to practice-oriented handling, clear configuration of all connections, operating and display elements, as well as to compact and robust construction. Well-planned technology and attention to detail.
Screw-mounted plug-in terminal block
The line adapter on the I/O module is problem-free. The link to the inputs and outputs, by way of screw-attached plug-in terminals, is simple and easy to service. The terminals permit pre-wiring, so that the device is first started at the putting-into-operation stage and links up to the bus and the 230V line in a matter of seconds. A swapping of the wires when changing the device is impossible.
A further plus-point: contact protection in the disconnected state is given at all times (Modules with 16A relays have screw-terminals).
Bus Connecting Terminal
The bus connection is also made via plug-in terminals. Like the bus-coupling-unit and the system clock, the REG-M I/O modules make use of the bipolar bus connecting terminal. In this way it is possible to make up to 4 bus connections to a single device. Another advantage: when disconnecting one device from the bus the bus itself is not interrupted. All other devices connected to the bus continue to operate normally.
Link-Power-Technology
The REG-M I/O modules use link power technology with LPT-10 transceiver to connect with the LON network. This enables the transfer of not only data, but also of energy, via the LON two-line network, for supply of the control electronics. A separate auxiliary voltage is therefore not required. Particularly in the case of decentralized application of the I/O modules, the wiring costs are reduced to a minimum.
Devices using link power technology can also be operated together with FTT-10-based devices in a common network sector.
Installation acc. to Instructions
Main power lines and bus connections (NYM or J-Y(ST)Y) may be positioned without separation. Isolated main-lines and bus connections must, however, be separated by 4mm or else provided with an equivalent-value insulation (EN-standards). In distributors it is often difficult to comply with the last requirement if additional bare main-lines are to be positioned next to the bus terminal with the bare wires of the bus connection. To ensure that the above specification is complied with, the I/O modules are provided with a protective cap that ensures a safe separation between main-lines and bus connections. |
